Thanks for that info on your shackle strap length, and the best option for an upgrade kit for shackle straps that measure 2-1/2 inches long from center to center bolt hole is the kit with 2-1/4 inch shackle straps:
- MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" Long Shackle Straps # MR46ZR
The # MR46ZR shackle straps are 2-1/4 inches from center to center of their bolt holes, so they are very close in length to yours, so you'll have the same amount of room for suspension... view full answer...
Weight distribution systems are rated by total tongue weight which is the tongue weight of your fully loaded and ready to tow trailer plus the weight of any cargo stored behind the rear axle of your tow vehicle.
The hitch weight of 456lbs mentioned is the unloaded hitch weight, and would not be correct to determine a weight distribution system.
The easiest way to get an accurate tongue weight rating is with a tongue weight scale like the # e99044, but there are other methods outlined... view full answer...
The Equa-Flex Cushioned Equalizers - Double Eye Springs - Tandem Axle - 3K to 6K # LC279687 is the correct equalizer for 33 inch or 35 inch spread. You will need to measure your current equalizer from center of hole to center of hole left to right. This system is 5-1/2 inches on center at rest. I've attached a video showing this equalizer on a 35 inch axle spread.
If your system requires a wider equalizer measurement like # K13-142-02, the Equa-Flex Cushioned Equalizers - Double Eye... view full answer...
The street bikes you want to carry with the Swagman e-bike rack # S94FR would need to weigh less than 70 lbs for the rack to have the needed capacity. So assuming your bikes weighed each 70 lb plus the weight of the carrier which is 60 lb this would put you at 200 lbs total which is less than the tongue weight capacity of the etrailer RV bumper hitch part # e38HR which is rated for 350 lb tongue weight.
So the hitch itself would be strong enough but what I can't answer is if your bumper... view full answer...
For a Dexter 3,000 lb trailer axle what you'd need to do is upgrade to the 3,500 lb trailer axle hub/drums like with the # AKHD-545-35-EZ-K which fits your spindle and then would allow you to install a set of 3,500 lb trailer brake assemblies that are self-adjusting like the # AKEBRK-35-SA and you'd be set. The hub comes with bearings as well. view full answer...
The backup camera prep package on the Grand Design Imagine is designed for the Furrion Vision S Wireless RV Backup Camera System like part # FOS43TASF. In regards to install, you'd simply reuse the existing shark-fin bracket on the trailer making for a plug-in-play setup. This would leave you with an extra shark-fin bracket but the kits all come with them.
There are a few different variants of the Furrion Vision S Wireless RV Backup Camera System if you want to check them out in the link below. view full answer...
That really does look like a Fulton swivel jack base like what the part # FXP15W is designed to fit but without you confirming that it's a Fulton we can't guarantee it would work. view full answer...
The cushioning of the MORryde Rubber Upgrade Kit Part # MR47ZR will still work great with 3,500 lb axles like you have. This is a really good question but the horizontal cushioning would be the same for your axle capacity or the higher capacity axles as well. view full answer...
I do have an option for you but there won't be a replacement converter you can install in your existing panel to charge lithium batteries. The entire panel would need to be replaced for which we have the Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger part # PD4135K. I spoke to Progressive Dynamics to confirm this for you. view full answer...
I recommend the MORryde Suspension Upgrade Kit # MR46ZR for your 2021 Grand Design Imagine XLS 22RBE, as it includes all new wet bolts, bronze bushings, nuts, and shackle straps to replace your current bolts and straps. This will save you from having to press all the bolts from your current straps and make replacement much simpler.
Be sure to use LubriMatic LMX Industrial Strength Grease # L11390 to fill the wet bolts. This grease is highly water insoluble so it will not dissolve when... view full answer...
In order to upgrade from the 5 on 4-1/2" bolt pattern to the 6 on 5-1/2" bolt pattern on a 2020 Grand Design Imagine XLS 23BHE you will need the Dexter Trailer Hub and Drum Assembly part # 84656UC3-EZ. The Dexter Trailer Hub and Drum Assembly will be a direct bolt-on swap.
Please note, you will have to get new wheels if swapping bolt patterns, I have 3 options for your to consider:
Your first option would be the Karrier ST225/75R15 Radial Tire # AM10303 with a Dexstar 15" White Spoke... view full answer...
Since your 2021 Grand Design Imagine 22RBE TT is prewired for a Furrion system, the best option is the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision - Rear Mount - 5" Screen # FOS05TASF which only has a backup camera, or the # FCE48TASL-05 which has a backup camera and two side cameras.
Both of these options will wire in easily to your prewiring and will do a great job of showing your surroundings with its 720 x 480 resolution and the 5" screen giving you a large monitor... view full answer...
Since we know your Grand Design Imagine XLS 22MLE has 3,500 lb axles the Road Armor Shock Absorbing # LC696740 will work in that regard. You'd need to measure the distance between the mounting holes of your current equalizers but as long as they are close to 6 inches and vertically between the lower holes and upper holes the dimension is close to 3-1/2 inches you'd be set. view full answer...
Your 2020 Grand Design travel trailer is only wired for a Furrion camera system like the one found in the # FOS43TASF, but you do have a couple of different options as to what size monitor you want and how many cameras you want to be able to connect to it. If you're only looking for a single camera system and you're ok with the smaller monitor, the Furrion # FOS43TASF is what you need. There are some better options with larger monitors and the ability to connect more cameras.
As far as... view full answer...
Murphy beds can use standard types of mattresses like the Denver Mattress Rest Easy Plush # DE29ZR that you referenced as long as the dimensions are compatible. This mattress measures 75" long x 60" wide x 5" tall. view full answer...
For your 2023 Grand Design Imagine 17MKE the best cover is the Adco Olefin HD part # AD97ZR. This provides the best protection, has zippered panel access to side of camper when covered, and has the easiest install due to having weighted straps that you can throw under the camper instead of having to climb under it. The overall weight of the cover is 25 lbs too so it's not overly heavy for how protective it is in your climate. This cover also provides the best protection in winter climates too. view full answer...
For bolts that do not have the zerk fittings we have the # 007-003-01 you can use and then for never fail bushings you could then use the part # TRBU11566. These parts aren't available in a kit. view full answer...
The best storage cover for your 2021 Grand Design Imagine XLS 22MLE is the Adco part # 290-52244 which is the correct size, offers the best protection in winter climates, is the easiest to install, and has zippered panels that allow you to to access side doors if ever needed. view full answer...
Yes, the Adco Olefin HD part # AD67ZR is the correct size cover for your 2022 Grand Design Imagine XL 22MLE and it's the best option so it would be what I would recommend. It offers the best protection and the easiest install plus it has access panels on the sides to give you access to side doors as needed as well. view full answer...